How to Panelized Different PCB Boards on AD Software

Published on 1/14/2019 7:10:14 PM

Description

The panel board is to combine multiple separate boards (boards that are not connected to each other) into one board for casting. In this case, a variety of boards can be produced at one time, and the speed is very fast, and the general price is cheaper than the <a href="https://www.allpcb.com/single_pcb_production.html" target="_blank">single PCB</a> proofing (batch).   The puzzles are usually connected using V-Cut or stamp holes. V cutting is to use a V cutting machine on the board to draw a knife on the upper and lower sides of the board, so it is easy to move by hand. The stamp hole is a pad or via that uses a stamp hole to connect the boards.   The jigsaw operation is very simple. First, draw the board, then create another PCB file as the board for the board, copy all the original boards, and then make a special paste on the file used for the board (shortcut EA). For example, draw a small board as shown below:   <img width="554" height="407" src="https://file.allpcb.com/bbs/19/01/14/190232938.png" />    Now you need to make this small board perform the puzzle operation, select all the copies, and then make the special EA paste in the puzzle file. When pasting, select “Duplicate designator” and then click “Paste Array”, or click “Paste”, “Paste Array" is to paste multiple at once, select "Paste Array" and enter the matrix paste option:   <img width="338" height="224" src="https://file.allpcb.com/bbs/19/01/14/190247898.png" />    X-Spacing indicates the horizontal spacing of the pasted multiple small plates. If the width of the small plate is equal to the width of the small plate, the pasted small plates are arranged seamlessly. Generally, the V cut is used.   More than the width of the small plate, there is a gap in the middle of the pasted small plate, and the stamp hole can be placed. Can not be smaller than the width of the small board, otherwise the two boards overlap, and the fool knows that this is not acceptable.   Then I repeated the E-A-Paste Array operation and placed the copied board reasonably to get a 5x3 large board:   <img width="389" height="433" src="https://file.allpcb.com/bbs/19/01/14/190302918.png" />    And added a 3mm process edge on the left and right sides, which is convenient for SMT patch. So I made a puzzle. I made a large board called 1SET, and a large board has 5x3=15 small boards called 15pcs. When cutting V, you need to have a line that identifies the V-cut track. You can also draw a V-cut line on a Machanical Layer and mark this layer as the V-CUT layer. You can also draw directly on the KeepOut Layer, and then communicate with the <a href="https://www.allpcb.com/pcb_manufacturer_service.html" target="_blank">PCB manufacturer</a>, indicating that this is a puzzle, using V cut in the middle for cutting.   When using a stamp hole to make a flat sheet, it is more troublesome than V cutting. When special paste is used, select Paste, then arrange a plurality of boards and then add a stamp hole connection between the boards. For example, there is a board that is drawn to be assembled as follows.   <img width="329" height="400" src="https://file.allpcb.com/bbs/19/01/14/190318867.png" />    Next, perform the jigsaw operation. Create an empty PCB file for the same piece as the previous operation, and then make a special paste. Add a stamp hole between the board and the board. The result is as follows:   <img width="483" height="293" src="https://file.allpcb.com/bbs/19/01/14/190336867.png" />    I simply designed the stamp hole here.   <img width="166" height="223" src="https://file.allpcb.com/bbs/19/01/14/190351170.png" />    In addition, it will be explained that there will be a lot of green errors after copying the original board to be assembled, because the network label is wrong after copying, and the rules of the newly created PCB file are the default rules. It is best to change the rules into the rules of the board to be assembled, so that you can get rid of a lot of mistakes (that is, green places), but you can't remove them all at once. In fact, you don't have to vote directly, but you can do "Reset" for good looks. Error Markers", the shortcut is TM, which removes all green.

comment

All comments

dong

4543

Go to Order My Own PCB

Rules about cashback: 1. Valid time: ALLPCB cashback activity will end on April 1st. 2. Capped amount: The capped amount of cashback for each account is $5,000. Each order can get a maximum of $2,000 cashback. That means every author can get $5,000 max. 3. Cashback range: The cashback activity only covers the corresponding PCB order. The order amount for other combined payment products will be invalid. 4. Clicking your own promotional link will be invalid. The same email address, shipping address, contact information, and phone number are all recognized as the same account. 5. ALLPCB has the final interpretation right of the cashback activity.

ALLPCB will donate 2% to the author for this promotion link.

Other Projects

Home / Industrial Automation low Cost with Arduino an ESP01

2552

314

Alternate Text josemarjr