World's Fastest PCB Manufacturing
My Message
Suggestions
Account

Get started now

Log In

or

Sign Up

My ALLPCB

My Orders Shipping Address Balance Account Settings My SNS Profile
0
  • Home
  • Instant Online Quote Alternate Text
    • PCB Instant Quote
    • PCB Assembly Quote
    • SMD-Stencil Quote
  • PCB Assembly
  • PCB Capabilities
  • Feedback
  • Resources
    • Sponsorship
    • PCB Softwares
    • Units Conversion
    • FAQ
  • About Us
    • About Us
    • Why Us
    • Contact Us
    • News
Log In Sign Up
  • Home
  • Instant Online Quote
    • PCB Instant Quote
    • PCB Assembly Quote
    • SMD-Stencil Quote
  • PCB Assembly
  • PCB Capabilities
  • Feedback
  • Resources
    • Sponsorship
    • PCB Softwares
    • Units Conversion
    • FAQ
  • About Us
    • About Us
    • Why Us
    • Contact Us
    • News
service@ALLPCB.com
Thank you very much for your valuable suggestion!
We will solve it as soon as possible!

The misunderstanding for Power Supply

2017/1/23 4:13:47

A power supply is an electronic device that supplies electric energy to an electrical load. The primary function of a power supply is to convert one form of electrical energy to another and, as a result, power supplies are sometimes referred to as electric power converters.
Power supply is very closely connected with our daily life, and we see them almost everywhere, cell phone, TV, computer, LED lightings, automotives, transformer substation, trains, airplane, etc. However, there has been some misunderstanding about power supply, here is a list about it.
1. Power-supply design is easy.
It seems many digital engineers take power for granted, but power supplies are being scrutinized as supply voltages keep decreasing. Supply tolerances are tightening as engineers work to decrease power, increase yield, and minimize supply-induced noise. Power-supply designs must address ripple, noise, spikes, compression, load response—both dynamic and static—as well as supply-induced signal noise and jitter. Any noise or transients on power rails propagate throughout the system.
2. Power doesn’t matter.
Many nuances in a power-distribution network can cause serious problems even in a purely digital design. Issues may include SoCs not coming up properly due to clock and data jitter, or a supply voltage droop that decreases propagation delay through a digital device, potentially resulting in failures.
In some applications, such as data centers, power demands and inefficiencies resulting in heat are key limiting factors on density and require expensive cooling and connectivity. Clean power becomes ever-more important with increasing speed and density. Reducing signal amplitudes for faster switching requires reduced noise margins in power supplies.
3. Power is low tech.
In fact, power is a dynamic field with technology changes such as gallium nitride (GaN) offering smaller size, higher power, less heat loss, and efficiency improvements. There are also innovations from power-supply system-in-package (PSSiP) manufacturers that improve performance in supplies powering everything from IoT endpoints to mobiles, TVs, servers, and everything between that needs ac converted to low dc voltages.
4. Converting ac mains to low-voltage dc requires a buck regulator and transformer.
Certain techniques use innovative capacitive-based technology that eliminates the need for a buck regulator or a transformer in certain applications, depending on voltage and current requirements. And when a transformer is used, the preliminary capacitive stages allow for a smaller transformer, with lower-cost coil and windings.
5. Switched-capacitor-based conversion techniques are not cost-effective and cannot carry significant power.
Efficiently engineered capacitor-based, voltage-reduction stages allow such solutions to be cost-effective. Aligning stages in series rather than in parallel allows each stage's capacitors to be optimally sized to decreasing voltages proceeding through subsequent stages. In fact, it’s possible to supply power in the tens of watts with purely capacitive stages—no buck required.
6. A transformer is required for isolation.
A thoughtfully designed capacitor-based design can provide capacitive isolation, giving the required 4-kV isolation between the high-voltage mains and low-voltage dc. Care must be taken to ensure that this isolation is under hardware control, so that even in the case of a software failure, there’s never a DC path from input to output.
7. Switched-mode power supplies (SMPS) require many components from a number of vendors.
It does seem to be the case that many power-supply component vendors seem averse to increasing the level of integration—perhaps in order to avoid cannibalizing their existing component business. This opens up opportunities for a supplier to integrate most components onto a mixed-mode IC and place it with some discrete components on a PSSiP. Doing so can replace a 110-V ac to 3.3-V dc supply with 68 parts using a small 6-pin PSSiP.
8. Primary-side regulation (PSR) is less accurate than secondary side.
The PSR technique uses switching rates along with FET and capacitor selections to allow for an accurate reading of output voltage that provides 1% regulation accuracy—without the tertiary winding required by existing PSR techniques (see figure). This while eliminating the nine extra parts required by an opto-isolated secondary regulation scheme.
9. Switchers are noisy and present EMI challenges.
It’s true that by virtue of their inherent design characteristics, switching power supplies generate electromagnetic interference (EMI) composed of signals of multiple frequencies. It’s due to the fact that internal ac voltages are not pure sine waves, but square waves made up of the superposition of many higher frequencies per Fourier analysis. However, a number of techniques exist for minimizing noise generation, and for mitigating conducted and radiated EMI. Some techniques utilize much lower switching frequencies, which greatly alleviate EMI, crosstalk, and noise concerns.
10. Power-supply efficiencies are tuned for a small power range and decrease significantly at low power.
It’s true that buck-regulator efficiencies roll off steeply below about 50% of the full power they’re designed to carry. One way around this problem is to use a buck regulator when power demand is high, and automatically change to a capacitor-only mode when the buck's efficiency tails off.
  • 2279
  • 1
  • 365
Post Comment

    Eric Flores Solis

    2017/1/25 4:13:47

    Your article answered all my puzzles.

    You might like

    Craig

    • Threads

      2

    • Following

      0

    • Followers

      0

    PCB Prototype

    PCB Instant Quote

    x mm

    Quantity

    Quote Now

    PCB Assembly

    SMT-Stencil

    • 12
    Products & Service
    PCB Capabilities
    Aluminum PCB Service
    PCB Assembly Service
    SMT-Stencil
    Quotation & Feedback
    Online Auto-Quotation
    PCB Assembly Quote
    Quote by Salesperson
    Customer Reviews
    Customer Support
    FAQ
    Community
    Sponsorship
    Referral Program
    About Us
    About Us
    Why Us
    Contact Us
    News
    Resource Details
    PCB Software
    Units Conversion
    service@allpcb.com central_support@allpcb.com
    Follow Us:
    Facebook Youtube Twitter Tumblr Youtube
    Certification: Certification
    Our Preferred Partners: Our Preferred Partners

    Please send Gerbers to service@ALLPCB.com for quotation © ALLPCB.com,All Rights Reserved Privacy PolicySitemap

    Secure Site by GoDaddy.com This site has earned the McAfee SECURE certification.