World's Fastest PCB Manufacturing
My Message
Suggestions
Account

Get started now

Log In

or

Sign Up

My ALLPCB

My Orders Shipping Address Balance Account Settings My SNS Profile
0
  • Home
  • Instant Online Quote Alternate Text
    • PCB Instant Quote
    • PCB Assembly Quote
    • SMD-Stencil Quote
  • PCB Assembly
  • PCB Capabilities
  • Feedback
  • Resources
    • Sponsorship
    • PCB Softwares
    • Units Conversion
    • FAQ
  • About Us
    • About Us
    • Why Us
    • Contact Us
    • News
Log In Sign Up
  • Home
  • Instant Online Quote
    • PCB Instant Quote
    • PCB Assembly Quote
    • SMD-Stencil Quote
  • PCB Assembly
  • PCB Capabilities
  • Feedback
  • Resources
    • Sponsorship
    • PCB Softwares
    • Units Conversion
    • FAQ
  • About Us
    • About Us
    • Why Us
    • Contact Us
    • News
service@ALLPCB.com
Thank you very much for your valuable suggestion!
We will solve it as soon as possible!

Arduino WiFi Shield

2017/2/17 18:21:24

The shield most used in practice are those that expand the communication of the Arduino board and in particular those that allow to add a network connection to a TCP / IP.
The first shield of this kind were those based on Ethernet technology, which helps the Arduino to connect to a LAN based on Ethernet TCP / IP, and so to Internet.
The convenience of Wi-Fi is now known to all: no more cables to spread (which increases the cost and time of construction of any plant) and full freedom in the positioning of the different nodes of the wireless network.
One of the first companies to focus on Wi-Fi was theAsyncLabs, who proposed a famous WiFi shield, including the appropriate libraries.
What we propose is a new solution for Wi-Fi: this is a shield that the hardware was inspired by that of AsyncLabs, but in addition, we have provided a slot for microSD memory.
The basic component of the shield that we have made is a Wi-Fi moduleMRF24WB0MAmanufactured by Microchip.
The device is a Wi-Fi IEEE 802.11 RF transceiver, with a data rate between 1 and 2 Mbps, and with an internal antenna.
The WiFi shield supports both types of wireless networks infrastructure (BSS) and ad-hoc (IBSS) and is also allowed to connect to secure networks (cryptographers and are supported 64 and 128-bit WEP, WPA/WPA2 and TKIP, AES and PSK).
In our project is using the SPI connection for communication with the WiFi controller through the SDO, SCK and SDI (pin 32, 34 and 35) and, if necessary, can be reset using a button (P1 in the diagram).
Peculiarities of our shield is that it has a SD card slot (SD1 signed in the schematic), managed by Arduino always through the SPI port.
There is also a LED (LD1 signed) used to indicate whether the Wi-Fi is active or not, its management is implemented through a hardware port, so you usually can not be used by software. In the event that was needed precisely this port, you still have a jumper that, when opened, making it available again disconnect the LED pin I / O.
Finally, to complete the hardware of the shield there is a section dedicated to the power, consists of a 3.3 Vvoltage regulator(indicated with U2).
BOM
[code]
R1: 4,7 kohm (0805)
R2: 4,7 kohm (0805)
R3: 4,7 kohm (0805)
R4: 4,7 kohm (0805)
R5: 1 kohm (0805)
R6: 4,7 kohm (0805)
R7: 2,2 kohm (0805)
R8: 1 kohm (0805)
R9: 2,2 kohm (0805)
R10: 1 kohm (0805)
R11: 2,2 kohm (0805)
R12: 330 ohm (0805)
C1: 220 µF 6,3 VL (D)
C2: 220 µF 6,3 VL (D)
C3: 100 nF (0805)
C4: 100 nF (0805)
C5: 100 nF (0805)
LD1: Led (0805)
U1: MRF24WB0MA/RM
U2: TC1262-3.3 (SOT-223)
SD1: µSD-Card (MICROSDSOCK2)
P1: switch SMD
Varie:
– headers  male 2 via
– headers  M/F 6 via(2 pz.)
– headers  M/F 8 via(2 pz.)
– headers  M/F 3 via(2 pz.)
– Jumper
– PCB
  • 2337
  • 1
  • 248
Post Comment

    Enrico Gensale

    2017/2/19 18:21:24

    Great work. I really appreciate it.

    You might like

    c.sirb

    • Threads

      4

    • Following

      0

    • Followers

      0

    PCB Prototype

    PCB Instant Quote

    x mm

    Quantity

    Quote Now

    PCB Assembly

    SMT-Stencil

    • 12
    Products & Service
    PCB Capabilities
    Aluminum PCB Service
    PCB Assembly Service
    SMT-Stencil
    Quotation & Feedback
    Online Auto-Quotation
    PCB Assembly Quote
    Quote by Salesperson
    Customer Reviews
    Customer Support
    FAQ
    Community
    Sponsorship
    Referral Program
    About Us
    About Us
    Why Us
    Contact Us
    News
    Resource Details
    PCB Software
    Units Conversion
    service@allpcb.com central_support@allpcb.com
    Follow Us:
    Facebook Youtube Twitter Tumblr Youtube
    Certification: Certification
    Our Preferred Partners: Our Preferred Partners

    Please send Gerbers to service@ALLPCB.com for quotation © ALLPCB.com,All Rights Reserved Privacy PolicySitemap

    Secure Site by GoDaddy.com This site has earned the McAfee SECURE certification.