World's Fastest PCB Manufacturing
My Message
Suggestions
Account

Get started now

Log In

or

Sign Up

My ALLPCB

My Orders Shipping Address Balance Account Settings My SNS Profile
0
  • Home
  • Instant Online Quote Alternate Text
    • PCB Instant Quote
    • PCB Assembly Quote
    • SMD-Stencil Quote
  • PCB Assembly
  • PCB Capabilities
  • Feedback
  • Resources
    • Sponsorship
    • PCB Softwares
    • Units Conversion
    • FAQ
  • About Us
    • About Us
    • Why Us
    • Contact Us
    • News
Log In Sign Up
  • Home
  • Instant Online Quote
    • PCB Instant Quote
    • PCB Assembly Quote
    • SMD-Stencil Quote
  • PCB Assembly
  • PCB Capabilities
  • Feedback
  • Resources
    • Sponsorship
    • PCB Softwares
    • Units Conversion
    • FAQ
  • About Us
    • About Us
    • Why Us
    • Contact Us
    • News
service@ALLPCB.com
Thank you very much for your valuable suggestion!
We will solve it as soon as possible!

About I2C Bus

2017/2/9 3:18:27

This article covers the essential characteristics and prominent advantages of the Inter–Integrated Circuit (aka I2C) serial-communications protocol.
Communicating via Alphabet Soup
It should come as no surprise that a common feature of electronic systems is the need to share information among two or three or ten separate components. Engineers have developed a number of standard protocols that help different chips communicate successfully—a fact that becomes apparent when you confront the barrage of acronyms under “Communications” in the list of features for a microcontroller or digital signal processor: UART, USART, SPI, I2C, CAN. . . . Each protocol has its pros and cons, and it is important to know a little about each one so that you can make an informed decision when choosing components or interfaces.
This article is about I2C, which is typically used for communications between individual integrated circuits located on the same PCB. Two other common protocols that also fit into this general category are UART (Universal Asynchronous Receiver/Transmitter) and SPI (Serial Peripheral Interface). You need to know the basic characteristics of I2C before you can thoroughly understand a comparison between these three interfaces, so we will discuss that topic at the end of this article.
Many Names, One Bus
There is no doubt that the I2C protocol suffers from a serious terminology problem. The actual name is Inter–Integrated Circuit Bus. The most straightforward—and probably theleastcommon—abbreviation is IIC. Perhaps this abbreviation has been disdained because the two capital I’s look like two 1s, or two lowercase l’s, or roman numeral II, or the symbol for parallel resistors. . . . In any event, the abbreviation I2C (spoken as “I squared C”) gained popularity, despite the questionable logic of treating a normal letter as if it is a variable subject to exponentiation. The third option is I2C (“I two C”), which avoids the inconvenience of superscript formatting and is also somewhat easier to pronounce than “I squared C.”
The final layer of fog settles in when you notice that SMB or SMBus is apparently used as yet another way of referring to the I2C bus. Actually, these abbreviations refer to the System Management Bus, which is distinct from, though almost identical to, the I2C bus. The original I2C protocol was developed by Phillips Semiconductor, and years later Intel defined the SMBus protocol as an extension of I2C. The two buses are largely interchangeable; if you are interested in the minor differences between them, refer to page 57 of the System Management Bus Specification.
Like Trying to Have an Important Conversation in a Room Full of People . . .
To appreciate the clever techniques that make I2C so effective, you need to think about the difficulty of achievingreliableyetversatilecommunication between multiple independent components. The situation is simple enough if you have one chip that is always the master and one chip that is always the slave. But what if you have multiple slaves? What if the slaves don’t know who the master is? What if there are multiple masters? What happens if a master requests data from a slave that for some reason has become nonfunctional? Or what if the slave becomes nonfunctional in the middle of a transmission? What if a master claims the bus to make a transmission then crashes before releasing the bus?
The point is,there are a lot of things that can go wrong in this sort of communication environment. You have to keep this in mind when you are learning about I2C, because otherwise the protocol will seem insufferably complicated and finicky. The fact is, this extra complexity is what allows I2C to provide flexible, extensible, robust, low-pin-count serial communication.
Overview
  • Only two signals (clock and data) are used, regardless of how many devices are on the bus.
  • Both signals are pulled up to a positive power supply voltage through appropriately sized resistors.
  • Every device interfaces to the clock and data signal through open-drain (or open-collector) output drivers.
  • Each slave device is identified by means of a 7-bit address; the master must know these addresses in order to communicate with a particular slave.
  • All transmissions are initiated and terminated by a master; the master can write data to one or more slaves or request data from a slave.
  • The labels “master” and “slave” are inherently non-permanent: any device can function as a master or slave if it incorporates the necessary hardware and/or firmware. In practice, though, embedded systems often adopt an architecture in which one master sends commands to or gathers data from multiple slaves.
  • The data signal is updated on the falling edge of the clock signal and sampled on the rising edge.
  • Data is transferred in one-byte sections, with each byte followed by a one-bit handshaking signal referred to as the ACK/NACK (acknowledge or not-acknowledge) bit.
I2C vs. UART and SPI
The advantages of I2C can be summarized as follows:
  • maintains low pin/signal count even with numerous devices on the bus
  • adapts to the needs of different slave devices
  • readily supports multiple masters
  • incorporates ACK/NACK functionality for improved error handling
And here are some disadvantages:
  • increases the complexity of firmware or low-level hardware
  • imposes protocol overhead that reduces throughput
  • requires pull-up resistors, which
    • limit clock speed
    • consume valuable PCB real estate in extremely space-constrained systems
    • increase power dissipation
We can see from these points that I2C is especially suitable when you have a complicated, diverse, or extensive network of communicating devices. UART interfaces are generally used for point-to-point connections because there is no standard way of addressing different devices or sharing pins. SPI is great when you have one master and a few slaves, but each slave requires a separate “slave select” signal, leading to high pin count and routing difficulties when numerous devices are on the bus. And SPI is awkward when you need to support multiple masters.
You may need to intentionallyavoidI2C if throughput is a dominant concern; SPI supports higher clock frequencies and minimizes overhead. Also, the low-level hardware design for SPI (or UART) is much simpler, so if you are working with an FPGA and developing your serial interface from scratch, I2C should probably be considered a last resort.
Conclusion
We have presented the salient characteristics of I2C, and we now know enough about the protocol’s pros and cons to allow for an informed decision on which serial bus you might choose for a given application. In future articles we will explore the protocol, and how to actually implement it, in more detail.
  • 1425
  • 1
  • 133
Post Comment

    usman

    2017/2/11 3:18:27

    A good piece of info for learning.

    You might like

    FRASER PHILLIPS

    • Threads

      6

    • Following

      0

    • Followers

      0

    PCB Prototype

    PCB Instant Quote

    x mm

    Quantity

    Quote Now

    PCB Assembly

    SMT-Stencil

    • 12
    Products & Service
    PCB Capabilities
    Aluminum PCB Service
    PCB Assembly Service
    SMT-Stencil
    Quotation & Feedback
    Online Auto-Quotation
    PCB Assembly Quote
    Quote by Salesperson
    Customer Reviews
    Customer Support
    FAQ
    Community
    Sponsorship
    Referral Program
    About Us
    About Us
    Why Us
    Contact Us
    News
    Resource Details
    PCB Software
    Units Conversion
    service@allpcb.com central_support@allpcb.com
    Follow Us:
    Facebook Youtube Twitter Tumblr Youtube
    Certification: Certification
    Our Preferred Partners: Our Preferred Partners

    Please send Gerbers to service@ALLPCB.com for quotation © ALLPCB.com,All Rights Reserved Privacy PolicySitemap

    Secure Site by GoDaddy.com This site has earned the McAfee SECURE certification.