Category:PCB PCB Layout

Group Administrators: 0 | Group Member: 86 | Group Threads: 106

The connections on a PCB should be identical to its corresponding circuit diagram, but while the circuit diagram is arranged to be readable, the PCB layout is arranged to be functional, so there is rarely any visible correlation.

Post A Thread
Search Results: 106 Threads,11 Pages
1 answers

Unable to edit the trace on bottom layer

When I do the PCB Layout, it is unable to click or highlight the traces on bottom layer. Why? (See More)

Chris Bethea
2016-08-17 17:30:17
Sebastian Charlak
2016-08-19 17:30:17
1 answers

Which is better between negative layer and positive layer?

Is it good to use GND plane to be a positive layer? If not, do you know whether there are any negative effects in this plane routed of signals? And which is much better between negative layer and pos... (See More)

Fredrick Lantz
2016-08-10 09:34:17
2016-08-12 09:34:17
1 answers

How to deal with standard difference signal lines in PCB layout

Hi, I have lots of questions about how to deal with standard difference signal lines in PCB layout. How are the standard difference signal lines rules when drawing differential lines in PCB layout? Wh... (See More)

Christever Rosario
2016-08-03 07:37:26
Adrian Wellings
2016-08-05 07:37:26
1 answers

PCB Layout DRC

In PCB layout, we use missing thermal to mark all GND via. Now, I had almost applied DCR.But missing thermal has been found on all of my GND vias. The software I use is CSiEDA 5.4 SE. Is it associated... (See More)

Pedro Skou
2016-07-22 18:18:36
2016-07-24 18:18:36
1 answers

Signal Return Path

Usually we make the return paths with nearest GND plane. What will happen if the signal return path on power planes? (See More)

2016-07-18 12:34:51
2016-07-20 12:34:51
1 answers

Double sided SMT board layout

When I making a PCB layout of my double sided PCB with components on sides, he component clearances made me mad. It reposts that components are too close even if they are on different sides. Any advic... (See More)

2016-07-06 20:30:48
Eduardo Gonzalez
2016-07-08 20:30:48
5 answers

The way of routing a 4 layer PCB

I am currently routing a 4 layers PCB and thinking how to connect the ground and power planes to the connector and components that need them. (See More)

2016-06-26 21:08:29
2016-12-13 11:59:48
2 answers

How Can I connect SMD components to ground plane?

I have some SMD components,but do you know the best way to connect them to ground plane?How about ground plane on both top and bottom with many vias connecting the two? (See More)

2016-06-26 16:30:40
Slaven Antolcic
2016-12-02 17:17:37
1 answers

Some questions about PCB layout design

Can you please tell me the method to laminate?And what's the meanning of L/S? (See More)

Theo van Eijken
2016-06-21 07:27:12
Michel Froehlich
2016-09-17 09:01:17
2 answers

What Should We Pay Attention to in High Current Path Routing?

There is a high current path in my PCB design from relay to output connector,that current rating is 15 to 20,amps max and voltage is 230 volt.How can I route the trace and what should I pay attention ... (See More)

Patrick Hamers
2016-06-15 16:27:42
Ignacio de la Fuente
2016-12-15 10:10:25
Post A Thread
Search Results: 106 Threads,11 Pages