Category:Electronic Components BGA

Group Administrators: 1 | Group Member: 95 | Group Threads: 100

A ball grid array (BGA) is a type of surface-mount packaging (a chip carrier) used for integrated circuits. BGA packages are used to permanently mount devices such as microprocessors. A BGA can provide more interconnection pins than can be put on a dual in-line or flat package. The whole bottom surface of the device can be used, instead of just the perimeter.

Thread Reply
BGA Design Tips Reply 2017-01-18 08:27:29
1K+ views
1 comments
494 likes

Buck

Leave A Message

Follow

Source: BGA NET COMPANY
I was asked by many PCB designers about BGA design guidelines, say ball PAD size, pitch size, annular ring, layer counts, solder mask opening, etc. There is no ready answer for it, because every BGA is different from one another, yet there are some rules and tips to follow to make better results. In this article, I am going to introduce them step by step.
There are 4 parts in the article as showing below:
1. The advantages of using BGA
2. How to avoid BGA design mistakes
3. BGA design rules
4. BGA PCB feature definitions
1. The advantages of using BGA
A BGA package is more advantageous at design layout because it provides increased functionality at the same package size compared to the Quad Flat pack (QFP). It improves the ratio of pin count to board size, hence providing more connections and increased area for routing.
A BGA package also offers better thermal and electrical performance. It does that by providing ground planes for a low impedance power system and controlled impedance on traces.
BGAs also offer reduced package thickness than those with pins. Moreover, BGA balls are considerably stronger than QFP leads and therefore can tolerate rough handling. This can potentially reduce the cost of ownership by virtue of their re-workability.
2. How to avoid BGA design mistakes
Today’s smaller packaging can create confusion to PCB designers. When designing with BGA with pitch sizes of 0.5mm and above, there are certain rules of thumb related to pad sizes and solder mask opening. One is to maintain pad size to about 85 % of a BGA’s ball size. Another is to use a non-solder mask defined (NSMD) pad. In this case, the solder mask is larger than the BGA pad.
The solder mask is usually opened to a diameter of about the ball size of the BGA. The recessed solder mask provides stress relief to the NSMD pad during reflow. In short, it creates a protective barrier and lets solder go around it.
Then, there are solder mask defined (SMD) pads, which are used for 0.4mm and below pitch BGA PCB designs. NSMD and SMD pad definitions and photos are shown in the bottom of this article. In the SMD pad case, the solder mask opening is smaller than the pad size. Better yields and results are achieved for these particular PCB designs.
Below are some tips to avoid BGA design mistakes.
1. Using NSMD pad sizes for 0.4mm pitch BGA PCB design may provide favorable results at low volumes, but chances are low yields result at high-volume production runs.
2. Keep in mind that ball size of 0.4mm pitch BGAs are smaller than those of 0.5mm pitch BGAs. Reducing pad size further may cause an insufficient solder-able area on the BGA pads. This can lead to PCBs being rejected at assembly inspection or latent failures in the field.
3. Bridging can be created between pads when using NSMD pads for 0.4- and 0.3mm pitch BGAs. Bridging is created because there’s not enough solder mask webbing between pads.
4. Since pad sizes are so small, and there is no solder mask webbing to provide adhesive strength, the pad may peel off, during reflow, or in the field. It’s best to have no trace between two BGA pads. Having them introduces shorts at pitches of 0.4mm and smaller on external layers.
5. On internal layers, there should be just one trace between pads. Also, PCB fabrication problems surface when running multiple and thin 2 to 3 mil traces between two BGA pads.
6. Make all vias solder mask covering; for the vias at BGA area, they should be via plugged. This is better for your assembly purpose.
3. BGA design rules
Figures are easier and better understandable than words, See below photo and diagram.
Conversion between mm and mils
0.075mm = 3 mils (0.003”)
0.1mm = 4 mils (0.004”)
0.125mm = 5 mils (0.005”)
0.2mm = 8 mils (0.008”)
0.4mm = 16 mils (0.016”)
0.45mm = 18 mils (0.018”)
0.5mm = 20 mils (0.020”)
4. BGA PCB feature definitions
Pitch-distance between the center of one ball to the center of the next one.
Via diameter - the full width of the via annular ring, also called PAD
Ball pads-Also called BGA "lands". This is the copper that the BGA ball solders to.
Micro via- a via that is laser drilled.
HDI- High Density Interconnect. This is the type of board that uses very small vias like micro vias. When a board uses micro vias it is called an HDI board.
The Quad Flat Package, or Quad Flat Pack, QFP, is a package used for surface mount, SMD integrated circuits
NSMD pad- Non-Solder Mask Defined ball pad. This kind of pad has an opening that is defined only by the size of the ball pad. The solder mask is applied around the ball pad and does not cover it. This kind of pad is more popular lately and has the advantage of increased ball adhesion because the ball flows around the sides of the ball pad and grips on the top and the sides. This kind of pad is usually recommended for BGA designs 0.5mm and above.
SMD pad - Solder Mask Defined ball pad. This kind of pad has a large copper area, but the solder mask covers the edges, so the opening is known as solder mask defined. This kind of pad is sometimes best for very small pitch pads where ball shorting is an issue.
494 likes
Statement: This post is only the personal view of the author and does not represent the opinions of ALLPCB.com.

David Russell

Leave A Message

Follow

Remarkable.It help me a lot. Thank you.
ThreadReply