Unique composite solution to make gas pipelines safer

2017/2/24 15:22:31

Haydale Composite Solutions (HCS, Loughborough, UK) has developed a revolutionary composite “gas transition piece” for UK’s utility company National Grid. The composite piece fits around high pressure natural gas transmission pipes to prevent water ingress at “transitions” where pipes pass through concrete inspection pits. In the current situation, without such seals, says Paul Ogden, a senior civil engineer with National Grid, the company would be forced to excavate and remove concrete surrounding the pipe to get a good look at the pipe’s condition. Plus, that transition point where the steel pipeline enters the fresh air of the pit is a “focus point” for corrosion of the steel. National Grid understandably is concerned about the potential hazards of removing the concrete around the pipe perimeter and risking damage to the pipeline.
The HCS Gas Transition Piece (GTP) solution is a series of molded composite segments that fasten together around the pipe’s annulus (see photo), designed to allow technicians to quickly remove it, easily inspect the pipe for any corrosion issues or damage, and then put it all back in a relatively simple operation. While details about the molded composite itself are proprietary, HCS’s technical director Nick Weatherby told CW that the key to the GTP’s application is a unique elastomeric hydrophilic gasket-type seal that swells to approximately 400% in volume in the presence of water. “The GTP is installed with the seals dry so there is a lot of clearance and the segments can be easily positioned. Once in place and exposed to moisture/water the seals expand over a period of about 24 hours and seal the interface between the GTP and the pipe. The process is reversible in that during prolonged dry spells the seal dries out, then returns to its original size when wet,” says Weatherby. The seals are manufactured by extrusion and are fabricated to fit the GTP with a series of cutting templates and special adhesives and grouts that are also hydrophilic. Again, details on the seals and the additives that go into the elastomer are proprietary. With the seal, the GTP forms a water-tight seal around the pipeline to help lessen corrosion in the transition zone.
Working closely in conjunction with the National Grid’s R&D department, Haydale was recently awarded a contract extension to develop 14 different GTP solutions for seven different pipeline diameters, from 300-1050 mm. Each size has a variant for use on sites where access to the pipe is restricted by lack of access. This will enable the GTP solution to be rolled out across the entire gas transmission network in the UK. National Grid has identified the need for a total of approximately 300 units, and work on the contract is likely to span the next 15 months or so.
After installation, the composite GTPs can be readily removed, without the need for heavy lifting equipment, excavation work nor demolition to cut through the concrete walls. Engineers can carry out rapid inspections of the pipeline with considerable time and cost savings. Weatherby adds, “We have been working in infrastructure for 25 years and the GTP idea builds on that experience. The sealing system prevents ingress of water, sand or debris that might cause abrasion. To remove with the seals expanded, the GTP comes complete with a series of jacking pins that ease out the segments for inspection.” The bottom line: GTPs dramatically reduce the risk of damaging a large high-pressure transmission pipe and offer huge savings on time and cost for pipe inspection.
National Grid's Ogden says “During the next 6 years, up to 60 of these units are likely to be installed in the National Transmission System and will significantly improve safety as well as creating savings of up to £5 million in the next five to ten years, with further savings beyond that."

mehran

2017/2/26 15:22:31

A good piece of info for learning.

grzes91

2017/2/26 15:22:31

I have share it with my classmates. They all appreciate it a lot.

christian.holmberg

2017/2/26 15:22:31

It is pretty helpful to my daily learning.

You might like

yashchabria

  • Threads

    4

  • Following

    0

  • Followers

    0

PCB Prototype

PCB Instant Quote

x mm

Quantity

Quote Now

PCB Assembly

SMT-Stencil