Category:Electronic Components Capacitors Technology

Group Administrators: 1 | Group Member: 26 | Group Threads: 22

A capacitor is a passive two-terminal electrical component that stores electrical energy in an electric field. The effect of a capacitor is known as capacitance.

Thread Reply
Why the Capacitor in The Power Supply Filter is So Big? Reply 2017-01-21 18:53:53
2K+ views
1 comments
406 likes

Luis Moreno

Leave A Message

Follow

All AC-DC converters, whether they are linear supplies or have some kind of switching element to them, require a mechanism to take the varying power on the AC side and produce a constant power on the DC side. Typically a large filter capacitor is used to absorb and store energy when the AC power is higher than what is needed by the DC load and to supply energy to the load when the AC power is lower than what is needed. Regardless of the specifics of what is inside the converter block, all converters will have a varying input power and require a constant output power.
(Note: This illustration assumes that the power factor at the AC side is 1, so the converter needs to include power factor correction. At the end of this article, you can see how the equation for AC power was derived)
The input power on the AC side is \[p_{ac}(t)=P_{o} + P_{o}cos(2 \omega t)\] while the output power on the DC side is \[P_{o}\]. The ripple power part (\[ P_{o}cos(2 \omega t)\] - which is also highlighted in the graph of the diagram) needs to be eliminated by a filter in the converter.  This solution is easy and cost effective, but as we will see the filter capacitor stores far more energy than what is actually required for the filtering process.
An example system with a line frequency of 60 Hz, an output power of 700W at 390V and a maximum ripple of 8V, requires a capacitance of 595uF. 
The capacitor is doing its job by absorbing energy from the AC source when AC power provided exceeds the DC power needed and returning energy to the DC load when the AC power provided is less than the DC power needs. The problem is that most of the energy stored in the capacitor is not being used. It is only the small amount of power flow that generates the voltage ripple that is actually being processed by the capacitor. All of that unused stored energy must be in the capacitor, though, to get the voltage of the capacitor up to the voltage required at the output. It's kind of like having a 10,000 liter barrel of water with the spigot placed a few centimeters from the top: the barrel has to be nearly full in order to get any water out, and you can only get water out until it is just below the spigot, then you have to refill it again. All of the water below the spigot is unusable. In the filter capacitor, all of the energy stored--except for the little bit absorbed and released during the voltage ripple--is similarly unusable because you need to keep the output voltage as constant as possible.
If you could design a circuit where you could control the power ripple to a capacitor to match the power ripple of the AC side of the converter and allow the voltage to swing as much as you want, you would have an effective filter that would significantly reduce the double line frequency ripple. The best part of this circuit would be that the capacitor would not have to store any extra energy just to be able to work. The voltage, current and power signals to such a capacitor would look something like this:
The design of such a circuit is possible. One way that you can create this kind of a circuit is to add a power processing or ripple port that is separate from both the AC input and the DC output. This ripple port would require a storage component (i.e., the capacitor) and a control system to control the power to the port. Since the ripple port is separate from both the input and output ports, neither port imposes any restrictions on the voltage of the ripple port. As you will see, you can reduce the capacitance to an arbitrarily low value by allowing the peak voltage to the capacitor to be really high.
Several different ripple port designs have been investigated and described in the academic literature. One design that stands out for its simplicity as well as its indicated potential in the real world market due to its patent is a design by Krein, et al., discussed here.
The general idea of the design is that we want all of the ripple power (\[P_{o}cos(2\omega t)\]) to flow back and forth to the ripple port capacitor. To get this to happen, we need the ripple power equation to match the equation for the power to a capacitor. 
For the two sides of this equation to be equal, the amplitudes must be the same and the phase shifts 
The two elements that you have control over in this equation are the capacitor and the peak voltage to the capacitor (\[V_{c}\]). Let's go back to the 700W, 390V example we looked at earlier and outline how you would determine the peak voltage and capacitance for the ripple port. First you would decide on a peak voltage for the ripple port. In theory you could pick any voltage you want and the higher the voltage, the lower the capacitance could be, but for safety reasons, you would probably want to pick something less than or equal to the output voltage. 
We are not done yet, all that we have determined is the peak voltage and capacitance to use. Next, we need to determine the phase shift of the voltage to the capacitor compared to the AC input voltage. 
This probably seems like a lot of work considering that the alternative is to simply throw in a big electrolytic capacitor. The problem is that electrolytic capacitors have short life expectancies. Typically, they have shorter life expectancies than any other component in an electronic system, so in systems where decades or more life expectancy is required, electrolytic caps are not a good solution. Film capacitors have a much longer life, but unfortunately are much more expensive than electrolytics for the same capacitance. For example, a quick search of an online electronic component catalog shows that a 600uF, 600V electrolytic capacitor is about $20 while a film capacitor with the same ratings is about $200. A system using this kind of ripple port would be able to cost effectively use a film capacitor instead of an electrolytic because capacitance requirements would be reduced by so much. Of course, before using this kind of system, a cost analysis of the control system for the ripple port would have to be compared to the cost of just using a big (and expensive) film capacitor.
As a final note, the same kind of system can be used for inverters when you need to generate AC voltage from a DC source. The reliability issue with electrolytic capacitors really becomes an issue for photovoltaic panels with built in micro-inverters because these micro-inverters must be warrantied for 20-25 years. That time span is much longer than the expected life of an electrolytic capacitor under any conditions.
406 likes
Statement: This post is only the personal view of the author and does not represent the opinions of ALLPCB.com.

Waelson Negreiros

Leave A Message

Follow

Awesome post. Like it very much.
ThreadReply