Thank you very much for your valuable suggestion! We will solve it as soon as possible!

Category:PCB PCB Design Rules

Group Administrators: 0 | Group Member: 284 | Group Threads: 284

Initially PCBs were designed manually by creating a photomask on a clear mylar sheet, usually at two or four times the true size. Starting from the schematic diagram the component pin pads were laid out on the mylar and then traces were routed to connect the pads. If you have many questions of PCB Design, please come here!

Community > Groups > PCB Design Rules
Search Results: 284 Threads,29 Pages Post A Thread
0 comments
193 views

Key points of high-speed PCB design

The concept of high-speed PCB is only derived from a very vague comparison in the engineer's mind. Years ago, when digital circuits were just emerging, the rate was very low, and PCBs could basically ...(view more)

aaaa
2019/2/21 17:20:40
0 comments
153 views

A comparison of Multiple PCB design and EDA simulation tools

Evaluating the pros and cons of EDA design tools is a more controversial topic, and it is difficult to draw an authoritative conclusion. Because each tool has its own characteristics, corresponding to...(view more)

shatomedia
2019/2/19 13:52:39
0 comments
379 views

How to Use Allegro to Design Multi-layer PCBs?

The pcb multi-layer board is a special kind of printed board. Its existence "location" is generally special. For example, there will be pcb multi-layer board in the circuit board. This kind of multi-...(view more)

Jukka Ainali
2019/1/29 16:14:08
0 comments
370 views

Impedance Matching in High Speed PCB Design

The transmission at this time does not cause reflection, which means that all energy is absorbed by the load. Otherwise, there is energy loss in the transmission. In high-speed PCB design, the matchin...(view more)

Horlebein
2019/1/29 15:12:52
0 comments
255 views

Brief Talk About Heat Dissipation Of Aluminum PCB and Its Design Method

In order to solve the heat dissipation problem, aluminum PCB and some high-power IC are widely used in LED trace design. Aluminum PCB consists of copper layer, thermally conductive dielectric layer an...(view more)

Tamir Asaraf
2019/1/29 11:00:41
0 comments
202 views

Some Notes about PCB Panel

1. The outer frame (clamping edge) of the PCB panel should adopt a closed-loop design to ensure that the PCB panel will not be deformed after being fixed on the fixture;   2. PCB board...(view more)

Michele Deligio
2019/1/28 9:51:52
0 comments
179 views

Some Common Issues Identified During PCB Design Process

For designers or hobbyists, no matter what kind of software do you use for the design work, there are some common issues that may occur during the design process, Today in this essay, we will talk abo...(view more)

Ibrahim ARI
2019/1/25 14:34:24
0 comments
324 views

PCB Routing Principles

In PCB design, wiring is an important step to complete product design. It can be said that the previous preparatory work is done for it. In the whole PCB, wiring design process is the most limited, th...(view more)

Shahzad Rafiq
2019/1/23 17:39:54
0 comments
285 views

Four Steps to Help Ensure Successful PCB Board Design

A printed circuit board (PCB) is the body of an electronic product, and the performance, life, and reliability of the final product depend on the electrical system it constitutes. Products that have h...(view more)

MARCO AURELIO
2019/1/23 17:14:40
0 comments
452 views

How to Set Appropraite Hole Size During PCB Design

Preparation for PCB Design   1. Accurate schematic diagram. Includes complete schematic and netlist, formal BOM with component encoding. The PCB package of all devices in the schema...(view more)

Sotiris Katsis
2019/1/23 16:01:25

    Hot Groups

    New Groups