Category:PCB Arduino

Group Administrators: 1 | Group Member: 84 | Group Threads: 60

Arduino is an open-source electronics platform based on easy-to-use hardware and software. It's intended for anyone making interactive projects. About Arduino and Arduino Projects sharing are appreciated.

Thread Reply
Controlling a DC Motor by Using Arduino Reply 2017-01-22 19:14:05
1K+ views
1 comments
326 likes

Vasiliy

Leave A Message

Follow

By connecting an L298 bridge IC to an Arduino, you can control a DC motor.
A direct current, or DC, motor is the most common type of motor. DC motors normally have just two leads, one positive and one negative. If you connect these two leads directly to a battery, the motor will rotate. If you switch the leads, the motor will rotate in the opposite direction.
To control the direction of the spin of DC motor, without changing the way that the leads are connected, you can use a circuit called an H-Bridge. An H bridge is an electronic circuit that can drive the motor in both directions. H-bridges are used in many different applications, one of the most common being to control motors in robots. It is called an H-bridge because it uses four transistors connected in such a way that the schematic diagram looks like an "H."
You can use discrete transistors to make this circuit, but for this tutorial, we will be using the L298 H-Bridge IC. The L298 can control the speed and direction of DC motors and stepper motors and can control two motors simultaneously. Its current rating is 2A for each motor. At these currents, however, you will need to use heat sinks.
Hardware Required
  • 1 x L298 bridge IC
  • 1 x DC motor
  • 1 x Arduino Mega2560
  • 1 x breadboard
  • 10 x jumper wires
The schematic above shows how to connect the L298 IC to control two motors. There are three input pins for each motor, including Input1 (IN1), Input2 (IN2), and Enable1 (EN1) for Motor1 and Input3, Input4, and Enable2 for Motor2.
Since we will be controlling only one motor in this tutorial, we will connect the Arduino to IN1 (pin 5), IN2 (pin 7), and Enable1 (pin 6) of the L298 IC. Pins 5 and 7 are digital, i.e. ON or OFF inputs, while pin 6 needs a pulse-width modulated (PWM) signal to control the motor speed.
The following table shows which direction the motor will turn based on the digital values of IN1 and IN2.
IN1 IN2 MOTOR
BRAKE
1 FORWARD
1 BACKWARD
1 1 BRAKE
IN1 pin of the L298 IC is connected to pin 8 of the Arduino while IN2 is connected to pin 9. These two digital pins of Arduino control the direction of the motor. The EN A pin of IC is connected to the PWM pin 2 of Arduino. This will control the speed of the motor.
To set the values of Arduino pins 8 and 9, we will use the digitalWrite() function, and to set the value of pin 2, we will use the using analogWrite() function.
Below is a photo of the set up.
Setup
  1. Connect 5V and ground of the IC to 5V and ground of Arduino.
  • Connect the motor to pins 2 and 3 of the IC.
  • Connect IN1 of the IC to pin 8 of Arduino.
  • Connect IN2 of the IC to pin 9 of Arduino.
  • Connect EN1 of IC to pin 2 of Arduino.
  • Connect SENS A pin of IC to the ground.
  • Connect the Arduino using Arduino USB cable and upload the program to the Arduino using Arduino IDE software.
  • Provide power to the Arduino board using power supply, battery or USB cable.
  • The motor should now run first in the clockwise (CW) direction for 3 seconds and then counter-clockwise (CCW) for 3 seconds.
    326 likes
    Statement: This post is only the personal view of the author and does not represent the opinions of ALLPCB.com.

    Mikael

    Leave A Message

    Follow

    Nice content you’ve posted in here
    ThreadReply