Category:PCB Assembly PCB Assembly Service

Group Administrators: 0 | Group Member: 249 | Group Threads: 393

In assembly the bare board is populated with electronic components, called a "printed circuit board assembly" (PCBA). In through-hole technology, the component leads are inserted in holes surrounded by conductive pads; In surface-mount technology (SMT), the component is placed on the PCB so that the pins line up with the conductive pads or lands on the surfaces of the PCB.

Post A Thread
Search Results: 393 Threads,40 Pages
1 answers
156 views

Heatsink Press

We have an application where we are applying a heatsink with a thermal tape that has pressure sensitive adhesive (psa) on either side. Does anyone know of an off-the-shelf heatsink press that we could... (See More)

Ricardo Medda
2017-03-01 01:38:51
lkrzywanski
2017-03-03 01:38:51
1 answers
52 views

Does anyone have Panasonic CM202DS/CM402L or Assemblion Topaz & ACM?

I am currently looking at purchasing equipment and have narrowed it down to these two platforms. Does anyone have these machines or any input about them? (See More)

GABRIEL SILVA
2017-03-01 01:36:36
Elektro Doni
2017-03-03 01:36:36
1 answers
88 views

How to unlock conceptronic oven?

Hello All We have here a Conceptronic oven running under Win 3.1 and the password have been lost. Is there a trick to find it in some files or do we have to reload the firmware ? Thanks (See More)

Mike
2017-03-01 01:34:59
Koray
2017-03-03 01:34:59
1 answers
160 views

Siemens placement process optimization

Does anyone have any Siemens placement process optimization for picking and placing 0402's, especially the resistors. Any response is greatly appreciated. (See More)

yasarugur06
2017-03-01 01:34:36
kyleahampton
2017-03-03 01:34:36
1 answers
165 views

SMT 20 x 20 Quick Frame Stencil Adapter

Does anybody know where I can find an SMT 20 x 20 Quick Frame Stencil Adapter???? I've been hunting, and haven't had much luck. Let me know! Thanks! (See More)

juanbrito
2017-03-01 01:33:44
Bartosz Orzechowski
2017-03-03 01:33:44
1 answers
156 views

cold joint problems

we are facing cold joint problem in selected component please advise me possiblity of this problem (See More)

Jeroen
2017-03-01 01:26:33
Yaser Fath
2017-03-03 01:26:33
1 answers
156 views

PT500 application software

Hi lads, Can anyone tell me a bit about PT500 application software? I recently had to replace the Hard drive in the host PC for our wave. I re-loaded the system software and re-configured. One thing I... (See More)

Fly
2017-03-01 01:25:35
Leo Korbee
2017-03-03 01:25:35
3 answers
149 views

how often the optical sensor goes bad on the CS-400E machines

Does anyone know how often the optical sensor goes bad on the CS-400E machines. I have 2 machines and it seems that the optical correction does not work anymore. I keep getting an optical correction e... (See More)

Ricardo Medda
2017-03-01 01:22:43
Brady
2017-03-03 01:22:43
3 answers
220 views

wrinkles solder joints found on SOIC and SOT components

After 2nd time reflow of double reflow, wrinkles solder joints found on SOIC and SOT components.(only happen on the components at the underside of pcb during reflow, top side components dont have this... (See More)

Carter
2017-03-01 01:17:56
Richard Baggaley
2017-03-03 01:17:56
5 answers
55 views

set N2 Idle Time

Now I can use Idle gas mode but I want to set N2 Idle Time because it will work when the furnace empty instantly So, the question is How could I set N2 idle timer and pressure regulator (See More)

Florencia
2017-03-01 01:07:25
Vitor
2017-03-03 01:07:25
Post A Thread
Search Results: 393 Threads,40 Pages