Category:Electronic Components Component Learning

Group Administrators: 0 | Group Member: 347 | Group Threads: 426

Electronic components are basic electronic element or electronic parts usually packaged in a discrete form with two or more connecting leads or metallic pads. Electronic Components are intended to be connected together, usually by soldering to a printed circuit board (PCB), to create an electronic circuit with a particular function.

Post A Thread
Search Results: 423 Threads,43 Pages
4 answers
146 views

Siemens 80 S-20 problem

I just had to replace the hard drive in the SC and the MC. I partitioned the MC drive and installed all operating systems. The machine boots up and gets past "software booting", "conversion of m... (See More)

minh2611
2017-02-27 22:16:20
rlb-designs
2017-03-01 22:16:20
4 answers
50 views

Baking MSDs in tubes

Is anyone doing this? What is the proper temp to bake tubes at? Is there an easier solution? (See More)

fabian
2017-02-27 22:12:39
rosenborisov78
2017-03-01 22:12:39
5 answers
92 views

YAGEO wrong value resistor

Have just discovered wrongly labelled resistor from YAGEO RC0805FR-072K2L Date 200706, Which should be 2k2. Part is in fact 22r. (See More)

nestandart
2017-02-27 21:36:39
el.mehdi.fakir
2017-03-01 21:36:39
4 answers
121 views

Need a good rework station for connectors

We have an outdated Metcal rework station and are thinking about purchasing a new one. We need something that has heat profile capability. We don't really need anything automated, just something that'... (See More)

Scott
2017-02-27 21:29:33
Andrew
2017-03-01 21:29:33
5 answers
65 views

SMT Exhaust Vacuum Monitor

Does anyone use or have any simple wave/reflow oven exhaust monitors with a visual check (LED). I was going to design something crude resembling a fan with an electric winding (electric motor of... (See More)

hello
2017-02-27 21:17:30
Eduardo Gonzalez
2017-03-01 21:17:30
4 answers
197 views

Melf components

Hi, Can somebody tell if for melf components the x and z sizes are the same? Normally they are, but the machine's vision system sees only 60-70% of the x size due to light dispersion. The Z dimension ... (See More)

tomasarizacrespo
2017-02-27 21:12:43
Eric Flores Solis
2017-03-01 21:12:43
5 answers
52 views

RJ45 Connector short issue after wave

Hi all, Need advice how to fix RJ45 short issue after wave solder m/c .Few actions taken to resolve this issue but the outcome was inclusive which was 1. Modify wave pallet 2. Change conveyor setting ... (See More)

n0xas
2017-02-27 20:59:09
Chad
2017-03-01 20:59:09
5 answers
73 views

To solve tombstone

Hi, I am having problem on tombstone, The part is LF chip component 1005, and my solder paste is WS leded. tombstone is not in a deg angle but one side is soldered but the other side is just sitting o... (See More)

jongerde
2017-02-27 20:30:55
christian.holmberg
2017-03-01 20:30:55
4 answers
114 views

ASG BMEP-5T Press

Does any one have a manual on this press? I am having problems with mine during homing. It seems that the Z axis sensors are not seeing the Z axis and it runs into hard limits. (See More)

Chester
2017-02-27 20:15:33
Javier Martínez
2017-03-01 20:15:33
4 answers
171 views

IP3 head 1 not placing parts

Head 1 is not placing the parts in production. Same component is placed by head 2. Head 1 camera is camera 12 type and head 2 camera is type 8. Machine re-set done resent proper data and interchanged ... (See More)

buy
2017-02-27 20:08:22
sousmen
2017-03-01 20:08:22
Post A Thread
Search Results: 423 Threads,43 Pages